The OBDII trouble password of P0335 is well-known as a “hard” code, meaning severely detrimental to the operation of your Accord engine. More specifically the DTC P0335 represents a absence of signal indigenous the crankshaft position sensor. The crankshaft place sensor in your Honda Accord informs your ECU that the crankshaft speed and current location.

You are watching: 2000 honda accord crankshaft position sensor location

Without this data, the engine will either no run or run very poorly. Common symptoms are challenge starting or the engine might shut off randomly, producing a really dangerous case for not just the driver however the passengers together well.

Possible causes of OBDII check engine irradiate P0335Bad or weak batteryBad StarterBad crankshaft position sensorDamaged sensor harness

Today I’ll be showing you just how to service and also replace her crankshaft position sensor in a 2000 Honda Accord with a F23A1 VTEC SOHC engine.

The part number because that this part is 37840-P0A-A01 for the crankshaft position sensor in her Honda Accord. That can additionally be found under the component number of 37840-PAA-A01.


*

This How To adjust a Honda Accord Crankshaft position Sensor DIY guide assumes friend have already removed her driver next engine mount and supported her engine through a jack. Please inspect our how To adjust a Honda Accord timing Belt overview for an ext details.

Before you start our DIY overview on exactly how To adjust a Honda Accord Crankshaft place Sensor, you should disconnect the an unfavorable terminal on your battery. As proclaimed previously, this guide assumes you have the right to raise and also lower your F23 already, which is mandatory when an altering your timing belt.

*

Unplug your 4 pin connector the runs to her crankshaft place sensor in your Honda Accord. Here’s what your pigtail looks like placed to your F23A1. It’s secured by a 10mm bolt the runs through the earlier of your VTEC SOHC engine.

*

This harness to her crankshaft place sensor runs v your lower timing plate, which have to be eliminated to change a Honda Accord Crankshaft place Sensor. In bespeak to perform this, you must reduced your engine if still connected to her chassis, and remove the crankshaft pulley or harmonic balancer.

This may be complicated if you room working ~ above the ground v hand tools and don’t have a waiting compressor with the ideal air tools. Use a Honda crankshaft wrench, Moroso part number 61805 to appropriately loosen your crankshaft bolt without air tools.

*

With the bolt removed, friend should be able to wiggle off your crankshaft wheel and collection it safely to the side. Make sure eliminate your woodruff vital and save that together safe together your pulley.

*

Now you deserve to remove all the 10mm bolts that organize your reduced timing sheathe in place. Eliminate these special bolts and then make your method to the valve cover, girlfriend will require to earlier off the valve covering bolts the run through to the cylinder head.

Loosen all the valve sheathe bolts, but do no remove and gently loosen her valve cover. Lift the valve covering to permit enough room for your upper SOHC VTEC timing cover to come off her engine. There are 2 10mm bolts the run v the top cover to the cylinder head, remove these to ease your top timing cover.

*

Now slide turn off your reduced timing cover and also pull down to relax from your side motor mount. You must now view your timing belt assembly and also your F23A1 balance shafts and belts. The crankshaft position sensor in her Honda Accord is located behind the crank cause plate.

*

You can take one of two routes to removing her crankshaft place sensor and replacing it. You have the right to loosen your timing belt tensioner bolt, the longated bolt situated in the middle of your tensioner arm. This should enable enough slack regarding gently earlier off your lower crank pulley-block plate and undo the 10mm bolt that holds the crankshaft place sensor in place.

*

If this is no an alternative for you, examine out our how To change a Honda Accord timing Belt guide on just how to correctly time and also remove your F23A1 belts to company your crankshaft place sensor.

There are several timing marks for your balance obelisk that us recommend you line as much as TDC before removing your balance obelisk belts.

See more: What Currency Is Used In Ireland, Currency Used In Southern Ireland

*

Before removing her balance obelisk belts come reach your crankshaft place sensor, girlfriend will need to twin check timing marks to ensure your F23a1 is at TDC. Again for much more details check our how To DIY overview on an altering the Honda Accord time belt.

*

Once you have actually replaced her Honda Accord crankshaft place sensor, you deserve to use a scan tool to effectively clear her OBDII examine engine password of P0335. Hope we’ve aided you learn exactly how To readjust a Honda Accord Crankshaft position Sensor, if girlfriend have any questions you re welcome leave us a comment below!